UNDERSTANDING THE PRINTER
Printer is one of the hardware (hardware) connected computer and have a function to print text, images and tampilanlainnya from computer to paper or similar media. The term is known padaresolusi printer called dpi (dots per inch). That is a large number titikdalam area 1 inch wide. The higher the resolution the better the prints produced. Conversely, if the resolution is low then the results cetakanakan bad / not good.
PRINTER PARTS
1) Casing printer
2) the operator panel
3) Place the paper feeds
4) Place the paper exit
5) The front cover
1) Casing printer
2) the operator panel
3) Place the paper feeds
4) Place the paper exit
5) The front cover
Printer parts
- Tray is a place to put the paper.
- Picker as a tool to take the paper from the tray.
- Ink or toner printer is a device that is used to write or print on paper. Ink and Toner have differences on the system. Require heating or laser toner, ink or inkjet while not need heating, just cleaning or cleaning the print-head printer.
- Flexible cable for signal transmission from the processor to the printer ink or toner. These cables are thin and flexible, yet powerful.
- On the back of the printer usually parallel or USB port for connecting to a computer.
- Tray is a place to put the paper.
- Picker as a tool to take the paper from the tray.
- Ink or toner printer is a device that is used to write or print on paper. Ink and Toner have differences on the system. Require heating or laser toner, ink or inkjet while not need heating, just cleaning or cleaning the print-head printer.
- Flexible cable for signal transmission from the processor to the printer ink or toner. These cables are thin and flexible, yet powerful.
- On the back of the printer usually parallel or USB port for connecting to a computer.
HOW TO
MAINTAIN THE PRINTER
1. The printer should be used regularly. Kedaan Do not leave the printer off for a long time. Turn on the printer at least 1 times 48 hours. If the colors do not just menggunaannya printer to print black only, use the same to print color images for all printer head work. If print quality has declined printer do the cleaning by doing print head clean with the facilities that already exist in the printer software. Do keep the print head clean up the quality improves.
2. In reload / refile, avoid touching the pin CMOS image while the crossed hands. Pin is extremely sensitive or may be damaged if exposed to static electricity in your body.
3. to avoid chemical reactions in the printer, then use the same brand of ink charging
remanufactured ink.
4. Use a neat paper when printing. It is intended that the print head is not easily damaged due to the uneven surface of the paper.
5. Clean tertur printer from dust and dirt. Use a small brush to be part of one in the printer can be affordable.
6. Use a cloth to cover the printer when not in use to avoid dust, do mentup printer too tight, as this may cause the printer to become moist, objec this can cause damage to printer components.
7. If the printer is often used (usually in the office - the office) do not turn off the printer after delesai used for printing, if the printer will be used again. Let the printer is turned on, this is to minimize over caunter hit, the limit caunter BIOS. Every printer has its limitations for printing typically 2000 times. Every time we turn on the printer then the counter will increase and considered 1 time scoring, just think we work for 8 hours and we turn off the printer 20 times in 8 hours of work, then the time to reset the counter in the BIOS.
8. Do not be too often print pictures or writing with a thick FILL it mengkibatkan head works hard so it will be easily damaged.
9. If your printer has been modified by using the infusion, it is better to put the infusion tube is parallel or lower than the printer, it is intended that the ink does not flow by itself when it is not active.
10. Clean foam or sponge sucking the rest of the ink from overflowing ink, ink may spill menyebebkan surge in electronic components printer. Cleaning sponge should be done once a year.
1. The printer should be used regularly. Kedaan Do not leave the printer off for a long time. Turn on the printer at least 1 times 48 hours. If the colors do not just menggunaannya printer to print black only, use the same to print color images for all printer head work. If print quality has declined printer do the cleaning by doing print head clean with the facilities that already exist in the printer software. Do keep the print head clean up the quality improves.
2. In reload / refile, avoid touching the pin CMOS image while the crossed hands. Pin is extremely sensitive or may be damaged if exposed to static electricity in your body.
3. to avoid chemical reactions in the printer, then use the same brand of ink charging
remanufactured ink.
4. Use a neat paper when printing. It is intended that the print head is not easily damaged due to the uneven surface of the paper.
5. Clean tertur printer from dust and dirt. Use a small brush to be part of one in the printer can be affordable.
6. Use a cloth to cover the printer when not in use to avoid dust, do mentup printer too tight, as this may cause the printer to become moist, objec this can cause damage to printer components.
7. If the printer is often used (usually in the office - the office) do not turn off the printer after delesai used for printing, if the printer will be used again. Let the printer is turned on, this is to minimize over caunter hit, the limit caunter BIOS. Every printer has its limitations for printing typically 2000 times. Every time we turn on the printer then the counter will increase and considered 1 time scoring, just think we work for 8 hours and we turn off the printer 20 times in 8 hours of work, then the time to reset the counter in the BIOS.
8. Do not be too often print pictures or writing with a thick FILL it mengkibatkan head works hard so it will be easily damaged.
9. If your printer has been modified by using the infusion, it is better to put the infusion tube is parallel or lower than the printer, it is intended that the ink does not flow by itself when it is not active.
10. Clean foam or sponge sucking the rest of the ink from overflowing ink, ink may spill menyebebkan surge in electronic components printer. Cleaning sponge should be done once a year.
Tidak ada komentar:
Posting Komentar